Qlogic QLogic 12000 Series Instalační příručka stáhnout pdf (Strana 23)

1–Installation

12800-040 Installation

D000140-001 D 1-13

Installation Tasks

1. Install the clip nuts. Install M6 clip nuts in the following locations on EIA rails:

Figure 1-8. Clip Nut Installation Locations

For improved stability, orient the clip nuts as shown (that is, orient the

flanges horizontally):

Figure 1-9. Clip Nut Orientation

2. Install support rails in the rack. Fasten with two (2) M6 screws per EIA rail to

pre-installed clip nuts and torque to 30 in-lb.

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 133 134

QLogic 12000 Series 1
Document Revision History 2
Table of Contents 3
Hardware Installation Guide 4
Intended Audience 7
Documentation Conventions 7
cd /root and press ENTER 8
License Agreements 9
Technical Support 9
Knowledge Database 10
1 Installation 11
Cable Requirements 12
Uninterruptible Power Supply 14
Installation Tasks Checklist 15
Mark the Rack 16
12200/12300 Installation 17
1–Installation 18
1-8 D000140-001 D 18
D000140-001 D 1-9 19
Installation 20
Figure 1-6. 12200 Hat Rails 20
D000140-001 D 1-11 21
12800-040 Installation 22
Installation Tasks 23
1-14 D000140-001 D 24
D000140-001 D 1-15 25
12800-120 Installation 26
D000140-001 D 1-17 27
1-18 D000140-001 D 28
D000140-001 D 1-19 29
1-20 D000140-001 D 30
D000140-001 D 1-21 31
1-22 D000140-001 D 32
D000140-001 D 1-23 33
12800-180 Installation 34
D000140-001 D 1-25 35
1-26 D000140-001 D 36
D000140-001 D 1-27 37
1-28 D000140-001 D 38
D000140-001 D 1-29 39
1-30 D000140-001 D 40
D000140-001 D 1-31 41
12800-360 Installation 42
D000140-001 D 1-33 43
1-34 D000140-001 D 44
1-36 D000140-001 D 46
D000140-001 D 1-37 47
1-38 D000140-001 D 48
D000140-001 D 1-39 49
1-40 D000140-001 D 50
D000140-001 D 1-41 51
1-42 D000140-001 D 52
D000140-001 D 1-43 53
1-44 D000140-001 D 54
D000140-001 D 1-45 55
1-46 D000140-001 D 56
Connecting Power 57
Figure 1-41. DC ON/OFF Switch 58
Guidelines 59
User Site Installation 60
Start-up Procedures 61
1-52 D000140-001 D 62
D000140-001 D 1-53 63
1-54 D000140-001 D 64
Enabling 8X Ports 65
Figure 1-49. 8X Ports Enabled 66
D000140-001 D 1-57 67
1-58 D000140-001 D 68
Figure 1-52. 8X Ports Enabled 69
1-60 D000140-001 D 70
Component LEDs 71
Chassis Status and Attention 72
Fault Tolerant 72
Service Required 72
MRL Active 72
Figure 1-55. MRL Active LED 73
Leaf Module 74
Spine Module 75
SEEB Module 76
12200 and 12300 77
12800 Fans and Power Supplies 78
Power Supply LEDs 79
1-70 D000140-001 D 80
Procedures 81
1-72 D000140-001 D 82
D000140-001 D 1-73 83
1-74 D000140-001 D 84
D000140-001 D 1-75 85
1-76 D000140-001 D 86
D000140-001 D 1-77 87
QLogic 12000 Six-Port Upgrade 88
1-80 D000140-001 D 90
A QLogic 12000 Series 91
Environmental Specifications 92
Power Specifications 94
Power Distribution Guidelines 96
Table A-4. AC Plug Types 97
D000140-001 D A-9 99
12800 Series 100
A-10 D000140-001 D 100
B Safety and Regulatory 101
Safety Information 102
B-2 D000140-001 D 102
Statement 2: 103
B-4 D000140-001 D 104
ステートメント 2： 105
Statement 3: 106
Uttalande 3: 107
Kijelentés 3: 107
Инструкция 3: 107
ステートメント 3： 107
Statement 4: 108
D000140-001 D B-9 109
Statement 5: 110
Uttalande 5: 111
Kijelentés 5: 111
Инструкция 5: 111
ステートメント 5： 111
Statement 6: 112
Kijelentés 6: 113
Инструкция 6: 113
ステートメント 6： 113
Statement 7: 114
D000140-001 D B-15 115
ステートメント 7： 116
D000140-001 D B-17 117
B-18 D000140-001 D 118
C Serial Port Pinouts 119
Serial Port Pinouts 120
C-2 D000140-001 D 120
P5-Rx P5 P6-Tx 120
P6-Gnd P4 P4-Gnd 120
P4-Tx P3 P5-Rx 120
D000140-001 D C-3 121
C-4 D000140-001 D 122
D FRU Replacement 123
QLogic 12300 124
Fan/Power Supply Replacement 125
QLogic 12800 Series 126
Replacement Procedures 127
Power Supply Replacement 128
Leaf Module Replacement 129
Spine Module Replacement 131
Management Module Replacement 132

Komentáře k této Příručce

Žádné komentáře

Qlogic QLogic 12000 Series Instalační příručka Strana 23

Komentáře k této Příručce

Související produkty a manuály pro Síťové přepínače Qlogic QLogic 12000 Series