Qlogic SANbox2-8c Instalační příručka Strana 231
- Strana / 256
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
B – Command Line Interface
Zone Command
59042-08 A B-123
0
Zone Command
Manages zones and zone membership on a switch.
Authority Admin session and a Zoning Edit session. Refer to the “Zoning Command” on
page B-129 for information about starting a Zoning Edit session. The List,
Members, and Zonesets keywords are available without an Admin session.
Syntax zone
add [zone] [member_list]
copy [zone_source] [zone_destination]
create [zone]
del
ete [zone]
list
members [zone]
remove [zone] [member_list]
rename [zone_old [zone_new]
type [zone] [zone_type]
zonesets [zone]
Keywords add [zone] [member_list]
Specifies one or more ports/devices given by [members] to add to the zone
named [zone]. Use a <space> to delimit aliases and ports/devices in
[member_list]. A zone can have a maximum of 2000 members. [member_list] can
have any of the following formats:
Domain ID and port number pair (Domain ID, Port Number). Domain IDs can
be 1–-239; port numbers can be 0–-255.
6-character hexadecimal device Fibre Channel address (hex)
16-character hexadecimal worldwide port name (WWPN) with the format
xx:xx:xx:xx:xx:xx:xx:xx.
Alias name
The application verifies that the [members] format is correct, but does not validate
that such a member exists.
copy [zone_source] [zone_destination]
Creates a new zone named [zone_destination] and copies the membership into it
from the zone given by [zone_source].
create [zone]
Creates a zone with the name given by [zone]. An zone name must begin with a
letter and be no longer than 64 characters. Valid characters are 0-9, A-Z, a-z, _, $,
^, and -. The zoning database supports a maximum of 2000 zones.
del
ete [zone]
Deletes the specified zone given by [zone] from the zoning database. If the zone
is a component of the active zone set, the zone will not be removed from the
active zone set until the active zone set is deactivated.
- Installation Guide 1
- Document Revision History 2
- Table of Contents 3
- Section 2 General Description 4
- Section 3 Planning 4
- Section 4 Installation 5
- Appendix A Specifications 6
- 59042-08 A Page vii 7
- 59042-08 A Page ix 9
- Page x 59042-08 A 10
- Introduction 11
- Related Materials 12
- New in this Release 13
- Safety Notices 14
- Sicherheitshinweise 14
- Communications Statements 15
- Statement 15
- CE Statement 16
- VCCI Class A Statement 17
- BSMI Class A Statement 17
- Laser Safety Information 18
- Accessible Parts 18
- Pièces Accessibles 18
- Zugängliche Teile 18
- General Public License 19
- Preamble 19
- 1 – Introduction 20
- 1-10 59042-08 A 20
- 59042-08 A 1-11 21
- 1-12 59042-08 A 22
- 59042-08 A 1-13 23
- 1-14 59042-08 A 24
- 59042-08 A 1-15 25
- Technical Support 26
- Availability 26
- Training 26
- Contact Information 26
- General Description 27
- Chassis Controls and LEDs 28
- Maintenance Button 29
- Resetting a Switch 29
- Chassis LEDs 30
- Over Temperature LED (Amber) 30
- Fan Fail LED (Amber) 30
- Heartbeat LED (Amber) 30
- Input Power LED (Green) 31
- Fibre Channel Ports 31
- Port LEDs 32
- Port Logged-In LED 32
- Port Activity LED 32
- Port Types 33
- Ethernet Port 34
- Serial Port 35
- Power Supply and Fan 36
- Switch Management 36
- SANsurfer Switch Manager 36
- File Transfer Protocol 38
- Planning 39
- Device Access 40
- Soft Zones 41
- Performance 42
- Distance 42
- Bandwidth 43
- Multiple Chassis Fabrics 44
- Optimizing Device Performance 44
- 3 – Planning 45
- 59042-08 A 3-7 45
- Common Topologies 46
- Cascade Topology 46
- Mesh Topology 47
- Multistage Topology 48
- Switch Services 49
- Fabric Security 50
- Connection Security 51
- Device Security 52
- 59042-08 A 3-15 53
- 3-18 59042-08 A 56
- 3-20 59042-08 A 58
- Switch_2 58
- 3-22 59042-08 A 60
- 59042-08 A 3-23 61
- MS Group: Group_1 61
- User Account Security 62
- 3-26 59042-08 A 64
- Installation 65
- Switch Power Requirements 66
- Environmental Conditions 66
- Installing a Switch 66
- Mount the Switch 67
- Install SFP Transceivers 68
- Configure the Workstation 70
- SANsurfer Management Suite 74
- SMS Installation for Windows 74
- 4 – Installation 75
- 59042-08 A 4-11 75
- SMS Installation for Linux 76
- SMS Installation for Solaris 78
- 59042-08 A 4-17 81
- 4-18 59042-08 A 82
- Configure the Switch 83
- Cable Devices to the Switch 85
- Install Firmware 85
- Powering Down a Switch 87
- 4-24 59042-08 A 88
- Diagnostics/Troubleshooting 89
- Heartbeat LED Blink Patterns 90
- System Error Blink Pattern 90
- Logged-In LED Indications 93
- E_Port Isolation 94
- Excessive Port Errors 95
- POST Diagnostics 96
- 5-8 59042-08 A 96
- Chassis Diagnostics 97
- Fan Fail LED is Illuminated 98
- Recovering a Switch 99
- Maintenance – Exit 100
- Maintenance – Image Unpack 100
- Maintenance – Copy Log Files 101
- Maintenance – Reset Switch 102
- Specifications 103
- Maintainability 104
- Dimensions 105
- Electrical 105
- Fabric Management 105
- Environmental 106
- Regulatory Certifications 107
- A – Specifications 108
- A-6 59042-08 A 108
- Command Line Interface 109
- User Accounts 110
- Modifying a Configuration 111
- Commands 114
- Admin Command 116
- Alias Command 117
- B – Command Line Interface 118
- B-10 59042-08 A 118
- CIM Command 119
- CIMListener Command 120
- 59042-08 A B-13 121
- CIMSubscription Command 122
- 59042-08 A B-15 123
- Config Command 124
- 59042-08 A B-17 125
- B-18 59042-08 A 126
- Create Command 127
- B-20 59042-08 A 128
- 59042-08 A B-21 129
- Date Command 130
- Firmware Install Command 131
- Group Command 132
- Keywords add [group] 133
- MD5 hash: 16-byte 134
- SHA-1 hash: 20-byte 134
- B-30 59042-08 A 138
- 59042-08 A B-31 139
- Hardreset Command 140
- Help Command 141
- History Command 142
- Hotreset Command 143
- Image Command 144
- Lip Command 147
- Passwd Command 148
- Ping Command 149
- Ps Command 150
- Quit Command 151
- Reset Command 152
- 59042-08 A B-45 153
- Security Command 160
- 59042-08 A B-53 161
- B-54 59042-08 A 162
- 59042-08 A B-55 163
- Securityset Command 164
- 59042-08 A B-57 165
- Set Command 166
- 59042-08 A B-59 167
- Set Config Command 168
- 59042-08 A B-67 175
- B-68 59042-08 A 176
- 59042-08 A B-69 177
- B-70 59042-08 A 178
- Set Log Command 179
- B-72 59042-08 A 180
- 59042-08 A B-73 181
- B-74 59042-08 A 182
- Set Port Command 183
- B-76 59042-08 A 184
- Set Setup Command 185
- B-84 59042-08 A 192
- 59042-08 A B-85 193
- B-86 59042-08 A 194
- Show Command 195
- B-88 59042-08 A 196
- 59042-08 A B-89 197
- 59042-08 A B-95 203
- B-96 59042-08 A 204
- 59042-08 A B-97 205
- B-98 59042-08 A 206
- 59042-08 A B-99 207
- B-100 59042-08 A 208
- 59042-08 A B-101 209
- Show Config Command 210
- 59042-08 A B-103 211
- B-104 59042-08 A 212
- Show Log Command 213
- B-106 59042-08 A 214
- 59042-08 A B-107 215
- Show Perf Command 216
- 59042-08 A B-109 217
- Show Setup Command 218
- 59042-08 A B-111 219
- B-112 59042-08 A 220
- 59042-08 A B-113 221
- Shutdown Command 222
- Test Command 223
- Uptime Command 226
- User Command 227
- B-120 59042-08 A 228
- 59042-08 A B-121 229
- Whoami Command 230
- Zone Command 231
- B-124 59042-08 A 232
- 59042-08 A B-125 233
- B-126 59042-08 A 234
- Zoneset Command 235
- B-128 59042-08 A 236
- Zoning Command 237
- 59042-08 A B-131 239
- B-132 59042-08 A 240
- Glossary 241
- Glossary-2 59042-08 A 242
- 59042-08 A Glossary-3 243
- Glossary-4 59042-08 A 244
- 59042-08 A Glossary-5 245
- Glossary-6 59042-08 A 246
- Numerics 247
- Index-2 59042-08 A 248
- 59042-08 A Index-3 249
- Index-4 59042-08 A 250
- 59042-08 A Index-5 251
- Index-6 59042-08 A 252
- 59042-08 A Index-7 253
- Index-8 59042-08 A 254
- Zoning command B-129 255
- Index-10 59042-08 A 256
Související produkty a manuály pro Síťové přepínače Qlogic SANbox2-8c
Síťové přepínače Qlogic SANbox2-8c Uživatelská příručka
(218 stránky)
(218 stránky)
Síťové přepínače Qlogic SANbox-8 Uživatelský manuál
(112 stránky)
(112 stránky)
(114 stránky)
Síťové přepínače Qlogic SANbox2-64 Instalační příručka
(202 stránky)
(202 stránky)
Síťové přepínače Qlogic SANbox 5602 Uživatelská příručka
(270 stránky)
(270 stránky)
Síťové přepínače Qlogic SANbox 5800V Series Specifikace
(422 stránky)
(422 stránky)
Síťové přepínače Qlogic SANbox2-8c Instalační příručka
(162 stránky)
(162 stránky)
Sanyo VDC-D1585VP manuels
Manuels d'utilisation et guides de l'utilisateur pour Caméras de sécurité Sanyo VDC-D1585VP.
Nous fournissons des manuels en pdf 1 Sanyo VDC-D1585VP à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentáře k této Příručce