Qlogic QConvergeConsole CLI 8200 Series Uživatelská příručka Strana 27
- Strana / 300
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
SN0054667-00 B 1-1
1 System Requirements
QConvergeConsole CLI is an management utility that centralizes management
and configuration of QLogic adapters within the entire network (LAN and SAN).
For optimum performance, QConvergeConsole CLI requires the hardware,
software, and operating systems listed in this section:
Hardware Requirements
Software Requirements
Operating System Requirements
Supported QLogic Adapters
Hardware Requirements
The minimum hardware requirements for the workstation server are as follows:
Server. Single-processor or multiprocessor server or workstation. See
“Operating System Requirements” on page 1-2 for a list of operating
systems.
Pentium
®
II processor, 300 MHz
Memory. 64MB of physical RAM to run QConvergeConsole CLI
Hard disk space. About 26MB disk space.
The minimum hardware requirements for the adapter are as follows:
Adapters. One or more of the QLogic adapters listed under “Supported
QLogic Adapters” on page 1-2.
- User’s Guide 1
- QConvergeConsole CLI 1
- Document Revision History 2
- SN0054667-00 B Page iii 3
- Page iv SN0054667-00 B 4
- Table of Contents 5
- 4 NIC Noninteractive Commands 6
- SN0054667-00 B vii 7
- SN0054667-00 B ix 9
- SN0054667-00 B xi 11
- 7 NIC Interactive Commands 13
- SN0054667-00 B xv 15
- SN0054667-00 B xvii 17
- Glossary 18
- List of Figures 19
- List of Tables 19
- What’s in this Guide 21
- What’s in the Help System 22
- Intended Audience 22
- Related Materials 22
- Documentation Conventions 22
- License Agreements 23
- Technical Support 24
- Knowledge Database 25
- 1 System Requirements 27
- Software Requirements 28
- Operating System Requirements 28
- Supported QLogic Adapters 28
- 1–System Requirements 29
- SN0054667-00 B 1-3 29
- 1-4 SN0054667-00 B 30
- Installing and Uninstalling 31
- 2-2 SN0054667-00 B 32
- Passive Windows Installation 34
- Environment 35
- 2-6 SN0054667-00 B 36
- 3 Getting Started 37
- 3–Getting Started 38
- 3-2 SN0054667-00 B 38
- Main Menu 39
- Menu Navigation 39
- Getting Help 40
- 4 NIC Noninteractive 41
- 4–NIC Noninteractive Commands 42
- Command Format 42
- 4-2 SN0054667-00 B 42
- -extloopback 44
- (CNA Information) 46
- -intloopback 47
- (Change Port Alias Name) 49
- (Change CNA Alias Name) 49
- (Port Information) 49
- -sreset 51
- -statport 52
- -sunreset 55
- -svmtool 55
- -teamdel 56
- -teaminfo 56
- -teamlist 57
- -teamnew 57
- -teamnew_portspreview 58
- -updimages_viewver 60
- -v, -ver 60
- -vlanadd 61
- -vlanadd_preview 61
- -vlandel 62
- -vlandel_preview 62
- -vlaninfo 63
- -vlanlist 63
- -vtcfgview 63
- -vtrestore 65
- 4-26 SN0054667-00 B 66
- -vtsave 67
- -zvt command as follows: 68
- 4-30 SN0054667-00 B 70
- 5 Fibre Channel 71
- Host Configuration 72
- Table 5-2. Command Variables 74
- (Show Parameter Settings) 77
- (Show Driver Settings) 82
- (Configure Driver Settings) 82
- 0 = Disabled, 1 = Enabled 83
- (Show HBA Statistics) 84
- (Set 85
- (Run Loopback Test) 87
- (Run Read/Write Buffer Test) 88
- Run a Read/Write Buffer Test 88
- (Display LUN Info) 93
- (Display Link Status) 93
- (Set Selected HBA Parameter) 96
- Description Name Alias Value 97
- (Output to a File) 98
- (Define Port Alias) 100
- (Update HBA Parameters) 102
- (Silent Mode) 103
- (Update Adapter Firmware) 103
- (Display Target Information) 104
- (Firmware Area Update/Save) 105
- (Target Beacon On/Off) 105
- (Display Host Topology) 105
- (Display Version) 106
- (Virtual Port) 106
- (Output in XML Format 1) 107
- (Output in XML Format 2) 107
- 5-38 SN0054667-00 B 108
- 6 iSCSI Noninteractive 109
- Command Summary 110
- -addchap 111
- -bootcode 112
- -bootcodemode 112
- -chapmap 113
- -cpbootcode 113
- -csbootcode 113
- -delchap 114
- -dspchap 115
- -dtdspa 116
- -dtdupd 116
- -edchap 118
- 6-12 SN0054667-00 B 120
- -import 121
- -ipdhcp 122
- -linkchap 123
- (Configure iSCSI Settings) 124
- -netconf 126
- -netconf6 127
- -pbootcode 129
- (Ping Target) 130
- (Update ROM Image) 131
- -sbootcode 133
- -sbootcodecid 133
- (Display Port Statistics) 134
- Adapter Information 138
- CNA Port Information (-pinfo) 139
- CNA VPD Information (-i) 140
- Adapter Configuration 141
- 7–NIC Interactive Commands 142
- 7-6 SN0054667-00 B 142
- Configure Port Settings 143
- Adapter Updates 144
- Adapter Diagnostics 145
- Register Test (-testregister) 146
- Hardware Test (-testhw) 146
- Loopback Test 147
- Link Test (-testlink) 147
- Adapter Statistics 148
- SN0054667-00 B 7-13 149
- 7-14 SN0054667-00 B 150
- 6. Refresh 150
- Help (-h) 151
- 7-16 SN0054667-00 B 152
- 8 Fibre Channel Interactive 153
- FC Port Information (-i) 155
- FC VPD Information (-i) 156
- FC Target/LUN Information 156
- HBA Parameters 158
- Display HBA Parameters (-c) 159
- Configure HBA Parameters (-n) 160
- Restore Defaults 161
- Display Configuration 162
- Bind Target(s) 162
- Unbind Target(s) 163
- Boot Devices Configuration 164
- Display Boot Device(s) (-e) 165
- Configure Boot Device(s) (-e) 166
- Primary Boot Device 166
- Target Link Speed (iiDMA) 167
- Basic Configuration 168
- Advanced Configuration 168
- Export (Save) Configuration 169
- Generate Reports 170
- Parameters Update (-r) 172
- Parameters Template Update 172
- Loopback Test (-kl) 174
- Display Test Parameters 175
- Reset Test Parameters 175
- Configure Test Parameters 175
- Read Write Buffer Test 176
- Display Test Parameters (-kr) 177
- Start Diagnostics Test (-kr) 178
- General (-dm) 178
- Details (-dm) 179
- Display Parameters (-gs) 181
- Reset Parameters 181
- Configure Parameters (-gs) 181
- Display FC Port Link Status 182
- Display Parameters 183
- Configure Parameters (-ls) 183
- Display Link Statistics (-ls) 184
- 8-34 SN0054667-00 B 186
- 9 Converged Network 187
- CNA Port Information 190
- SN0054667-00 B 9-5 191
- CNA VPD Information 192
- VPD information. For example: 193
- CNA VLAN Information 194
- Teaming Information 195
- CNA FCoE Information 195
- 9-10 SN0054667-00 B 196
- Information 197
- Data Center Bridging 197
- DCE Statistics 198
- SN0054667-00 B 9-13 199
- CNA iSCSI Information 200
- SN0054667-00 B 9-15 201
- 9-16 SN0054667-00 B 202
- CNA FCoE Configuration 204
- Display HBA Parameters 205
- Configure HBA Parameters 205
- Target Persistent Binding 207
- Display Boot Device(s) 210
- Configure Boot Device(s) 211
- Virtual Ports (NPIV) 212
- View vPorts Info 213
- Create vPorts 214
- Delete vPorts 215
- Driver Parameters 215
- Bind by World Wide Port Name 216
- Bind by Port ID 217
- Commit Changes 217
- Selective LUNs 217
- Display LUN Configuration 218
- Manual Configure LUNs 218
- SN0054667-00 B 9-33 219
- Auto Configure LUNs 220
- CNA iSCSI Configuration 223
- Display HBA Level Parameters 224
- Save changes and reset HBA 224
- Port Configuration 225
- Port Link Settings Menu 226
- SN0054667-00 B 9-41 227
- 9-42 SN0054667-00 B 228
- SN0054667-00 B 9-43 229
- 9-44 SN0054667-00 B 230
- SN0054667-00 B 9-45 231
- Port Restore Factory Defaults 232
- BIOS/UEFI Settings Menu 233
- 9-48 SN0054667-00 B 234
- Port IP Settings 235
- Display Network Settings 235
- Configure IP Settings 236
- Target Configuration 236
- List Targets 237
- Display Target Information 237
- Bind Target 238
- Delete Target 238
- Configure Target Parameters 238
- Add A Target 239
- Disable a Target 239
- Enable a Target 240
- SN0054667-00 B 9-55 241
- Target Discovery Menu 242
- For example: 243
- 9-58 SN0054667-00 B 244
- List LUN information 245
- Save Target/CHAP Changes 245
- Display BIOS/UEFI Information 246
- Set BIOS/UEFI Mode 246
- Set Alternative Client ID 247
- Save changes 248
- CNA NIC Configuration 249
- Adapter Alias 250
- Change Port Alias Name 252
- Change MAC Alias Name 252
- Save Port Configuration 252
- VLAN Configuration 253
- Display VLAN List 253
- Display VLAN Information 253
- Add VLAN to Port or Team 254
- Configure VLAN Parameters 255
- Remove VLAN from Port or Team 255
- Team Configuration 256
- Display Teams List 257
- Display Team Information 257
- Configure New Team 258
- Configure Team Parameters 259
- Delete Team 260
- Add Member(s) to Team 260
- Delete Member(s) from Team 260
- Set Primary Team Member 261
- Unset Primary Team Member 262
- Parameters Update 265
- Drivers Update 265
- Hardware Test 267
- Flash Test 267
- Interrupt Test 268
- Link Test 269
- 9-84 SN0054667-00 B 270
- Start Diagnostics Test 272
- Beacon/LED Test 275
- 9-90 SN0054667-00 B 276
- SN0054667-00 B 9-91 277
- 9-92 SN0054667-00 B 278
- SN0054667-00 B 9-93 279
- Ping Target 280
- SN0054667-00 B 9-95 281
- Display ARP Table 282
- Display Connection Error Log 282
- Display NIC Port Statistics 285
- Reset NIC Statistics 286
- Undo Reset NIC Statistics 286
- Display FCoE Port Statistics 286
- Display Test Parameters (-gs) 287
- Display HBA Statistics (-gs) 288
- Display FCoE Port Link Status 289
- Display iSCSI Port Statistics 291
- 9-106 SN0054667-00 B 292
- 9-108 SN0054667-00 B 294
- Glossary-2 SN0054667-00 B 296
- SN0054667-00 B Glossary-3 297
- Glossary-4 SN0054667-00 B 298
Související produkty a manuály pro Software Qlogic QConvergeConsole CLI 8200 Series
Software Qlogic Fast Fabric Uživatelská příručka
(142 stránky)
(142 stránky)
Software Qlogic QLA2000F Uživatelská příručka
(281 stránky)
(281 stránky)
Software Qlogic QLA2100F Specifikace
(243 stránky)
(243 stránky)
Software Qlogic OFED+ Host Specifikace
(20 stránky)
(20 stránky)
Software Qlogic QLA2102F Specifikace
(114 stránky)
(114 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.122 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce